Basic Tutorial
From Gerris
Very very simple tutorial
This is a step by step tutorial to GERRIS.
Gerris is a Partial Differential Solver (PDS) over the time-dependent incompressible variable-density Euler, Stokes or Navier-Stokes equations (and some variants). Gerris is also a progammation language and we begin now over the same basic concepts.
Gerris as a language
When we learn a language we begin always with words, then syntax, and then semantic.
Gerris language is composed by words that reflect the internal structure of the code. The Gerris code is written en C language with inheritances.
Gerris language is an inheritance language where the root of each word has a component of their parent.
By the way
- GfsOutputTiming (write summary of time consuming of the simulation)
- GfsOutputTime (write the model time, timestep, CPU time and real time)
- GfsOutputSimulation (write the whole simulation data)
have the same parent GfsOutput which write simulation data. If we understand the inheritance we do a big step forward.
In practice we write a code on a script line by line following the Gerris syntax and the Gerris solver interpret it.
Sample code : box
Simplest Gerris code doing nothing!!!
1 0 GfsSimulation GfsBox GfsGEdge {} { Refine 5 // Code Gerris here!! } GfsBox { // Boundary conditions here!! }
Gerris uses box of lenght L=1 (in 2D) or cubes (in 3D) to build a domain, in this case we use the 2D solver. We have
1 0 GfsSimulation GfsBox GfsGEdge {} {
1 0 says one box (1) not connected (0) and the other words (GfsSimulation GfsBox GfsGEdge) are Gerris reserved words.
The line
Refine 5
give us the initial mesh, we have created a regular Cartesian grid with 2*2*2*2*2=32 cells in each dimension. We ca use this Gerris word to refine the initial mesh.
200px|Refine 5 200px|"Refine 6"
The Figures show the mesh for Refine 3, Refine 5 and Refine 6. We can use every C expression like
Refine ( (y < x) ? 6 : 3 )
which gives Refine 6 for y < x and Refine 3 for y > x
The Figure show us two important things about Gerris structure
- y = x pass through the center of the box then the origin (0,0) is in the center of the box!! (Tip you can displace the origin using)
- We pass every mesh level one by one
Finally
GfsBox { // Boundary conditions here!! }
allows impose the Boundary conditions for our only box but you must to repeat GfsBox structure as many boxes as indicated in the first line.
Sample code : boundary condition for a box
A box has 4 sides (top, bottom, left and right) Gerris language uses these key words to impose the boundary conditions.
By default Gerris assumes that boundaries are solid walls with slip conditions for the velocity, we then have defined a rectangular box closed on all sides by solid walls.
Gerris uses two families of words
GfsBoundary and GfsBc
with the corresponding inheritances.
GfsBoundary is used to define boundary conditions on the boundaries for the box with the following syntax
GfsBoundary { [ GfsBc ] [ GfsBc ] }
where [ GfsBc ] are one of the descendants
* GfsBcDirichlet — Dirichlet boundary condition (i.e. value) * GfsBcNeumann — Neumann boundary condition (i.e. value of the normal derivative) * GfsBcNavier — Navier slip/Robin boundary condition
We note that GfsBoundary have also two particular descendants
- GfsBoundaryInflowConstant — Constant inflow
- GfsBoundaryOutflow — Free outflow/inflow
Example of Boundary conditions
Velocity U=1 at the left and outflow condition at the right
GfsBox { left = Boundary { BcDirichlet U 1 } right = BoundaryOutflow }
Pressure P=1 at the left pressure P=0 at the right
GfsBox { left = Boundary { BcDirichlet P 1 } right = Boundary { BcDirichlet P 0 } }
We note that we can use here : U, V, P as variables and every C function (including time t and espace x and y) like
GfsBox { left = Boundary { BcDirichlet U ( sin(2.*M_PI*0.05*t) ) } right = BoundaryOutflow }
a sinusoidal velocity at the lef side and outflow condition at the right side.
Sample code : first try
We can build now a simulation file for a box of length L=1, with a mesh of 32x32 (Refine 5) and with a input velocity equal to 1.
1 0 GfsSimulation GfsBox GfsGEdge {} { Refine 5 } GfsBox { left = Boundary { BcDirichlet U 1 } right = BoundaryOutflow }
We save the file as tutorial1.gfs and a console we run the simulation
gerris2D tutorial1.gfs
and nothing happens.
Sample code : intermezzo
We need to define necessarily the computational time and the output values of data.
- the Gerris word GfsTime defines the physical and the computational time (number of time steps performed) By default both the physical time and the time step number are zero when the program starts. It is possible to set different values using for example
GfsTime { t = 1.4 i = 32}
where i is the time step number and t is the physical time. The end identifier specifies that the simulation should stop when the physical time reaches the given value. It is also possible to stop the simulation when a specified number of time steps is reached, using the iend identifier. If both end and iend are specified, the simulation stops when either of these are reached. By default, both end and iend values are infinite.
GfsTime {end = 2 iend = 32}
- Gerris comes with a number of objects allowing to output specific data of the simulation. For that we need take a look to the GfsOutput a generic member which rely a given family (parent and childrens)
The parent of GfsOutput is GfsEvent which are used to control any action which needs to be performed at a given time during a simulation. The key words for GfsEvent are
start Physical starting time (default is zero). The "end" keyword can be used to indicate the end of the simulation. istart Time step starting time (default is zero). step Repeat every step physical time units (default is infinity). istep Repeat every istep time steps (default is infinity). end Stop at or before this physical time (default is infinity). iend Stop at or before this number of time steps (default is infinity).
The children of GfsOutput are .. a lot ... (rabbit family) we talk about many
- GfsOutputSimulation which write the whole simulation
the syntax is
GfsOutputSimulation {inheritance of GfsOutput, then of GfsEvent} file.gts
by the way
GfsOutputSimulation { start = 0.6 step = 0.3 } file.gts
which says, we write into a file file.gts every 0.3 of physical time starting from 0.6. The data format gts is a Gerris format and we will talk about later. Note that you can save data in your habitual format if you want.
- GfsOutputLocation which write the values of variables at specified locations
the syntax is
GfsOutputLocation {inheritance of GfsOutput, then of GfsEvent} data positionXYZ
by the way
GfsOutputLocation { step = 1 } data positionXYZ
which says do every physical step the following : write in file data the numerical values of the dynamical variables at positions given by the input file positionXYZ. The input file is a ascii file with the three columns of coordinates (x y z)
0 -0.5 0 0 -0.49 0 0 -0.48 0 0 -0.47 0 0 -0.46 0 0 -0.45 0 ...... 0 0.44 0 0 0.45 0 0 0.46 0 0 0.47 0 0 0.48 0 0 0.49 0 0 0.5 0
Sample code : second try
Finally we do the second try
1 0 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsTime {end = 5} GfsOutputLocation { step = 1 } data positionXYZ } GfsBox { left = Boundary { BcDirichlet U 1 } right = BoundaryOutflow }
this Gerris script do the following :
# it stops the run at 5 physical times GfsTime {end = 5} , # write the results into the file data at the given positions by the file positionXYZ, # the boundary conditions are imposed pressure at both ends
We save the file as tutorial2.gfs and a console we run the simulation
gerris2D tutorial2.gfs
and something happen but very strange signal... U = 1 everywhere, what's wrong?
Sample code : viscosity
We forget the viscosity!!! we take now a look to the Gerris documentation
By default, the density is unity and the molecular viscosity is zero (i.e. there is no explicit viscous term in the momentum equation). In practice, it does not mean that there is no viscosity at all however, because any discretization scheme always has some numerical viscosity. However, keep in mind that the only relevant parameter for the (constant density) Navier-Stokes equations is the Reynolds number. If you do not include any explicit viscous term the (theoretical) Reynolds number is always infinite.
So our script is wrong, good syntax but bad semantic!!! That says us that we have to think about the physical problem before!!!
We need set the viscosity, GfsSourceViscosity can do it
GfsSourceViscosity 'value or function'
for instance if we decide to do the simulation in a dimensionless variables (the good procedure) we can set the viscosity as 1/Re where Re is the Reynolds number
GfsSourceViscosity 1.
where the Reynolds number is now 1.
Sample code : third try
We write now
1 0 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsTime {end = 5} GfsSourceViscosity 1 GfsOutputLocation { step = 1 } data positionXYZ } GfsBox { left = Boundary { BcDirichlet U 1 } right = BoundaryOutflow }
this Gerris script do the following :
# it stops the run at 5 physical times GfsTime {end = 5} , # set the Reynolds number to 1. # write the results into the file data at the given positions by the file positionXYZ, # the boundary conditions are imposed pressure at both ends
We save the file as tutorial3.gfs and a console we run the simulation
gerris2D tutorial2.gfs
and it works!!
We take a look the the file data, there are several columns and the first line give the label of each column
# 1:t 2:x 3:y 4:z 5:P 6:Pmac 7:U 8:V 9:T
Using gnuplot (plot [0:0.1] "./data.dat" i 5 u 7:3 w lp) we can do a graph of the final time (t=5)
and the velocity U is constant!!! and where is our classical parabolic profile??
Sample code : fourth try
We set now all boundary conditions (top and bottom are set to zero)
1 0 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsTime {end = 5} SourceViscosity 1. GfsOutputLocation { step = 1 } data positionXYZ OutputSimulation { step = 1 } tt.gfs } GfsBox { left = Boundary { BcDirichlet U 1 } right = BoundaryOutflow top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } }
We save the file as tutorial4.gfs and a console we run the simulation
gerris2D tutorial4.gfs
and using gnuplot (plot [0:0.1] "./data.dat" i 5 u 7:3 w lp) we can do a graph of the final time (t=5)
Its better but it is not exactly a parabolic profile. Shear layer? We can look near the exit at coordinates (x = 0.45), recall that domain is [-0.5:0.5].
Using awk we modify the file positionXYZ to translate it toward the end
awk '{print $1+0.45 " " $2 " " $3 }' positionXYZ > positionX0.45YZ
and now we write
1 0 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsTime {end = 5} SourceViscosity 1. GfsOutputLocation { step = 1 } data positionXYZ GfsOutputLocation { step = 1 } data0.45 positionX0.45YZ } GfsBox { left = Boundary { BcDirichlet U 1 } right = BoundaryOutflow top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } }
where we generate two files data and data0.45. the results are
humm we will add a box
Sample code : adding a box
Now we add a box a right side of the our first box (the domain is now 2x1), 2 in x coordinates [(0.5:1.5)]. We generate also a new file positionX1.45YZ to study the profile at the end of the two boxes. We modify the Gerris file as following
2 1 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsTime {end = 5} SourceViscosity 1. GfsOutputLocation { step = 1 } data positionXYZ GfsOutputLocation { step = 1 } data0.45 positionX0.45YZ GfsOutputLocation { step = 1 } data1.45 positionX1.45YZ } GfsBox { left = Boundary { BcDirichlet U 1 } top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } GfsBox { right = BoundaryOutflow top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } 1 2 right
We have in the first line 2 1 which want say two (2) boxes with one (1) connection, and we add two GfsBox one for each box with the corresponding boundary conditions. The new line
1 2 right
say as that the boxes 1 and 2 are connected by the right side (beginning from the box 1)
Gfsview : a graphical tool
GfsView is a tool written specifically to visualize Gerris simulation files. We have seen the Gerris word GfsOutputSimulation before, we modify then our script adding the line
GfsOutputSimulation { start = end } file.gts
which says write the whole simulation on file file.gts at final time.
Now we can run Gfsview
Gfsview2D file.gts
and clicking on “Linear”, “Vectors” in the tool-bar and changing the vector length by editing the properties of the “Vectors” object (select the object then choose “Edit→Properties”) you should be able to get something looking like
You can also pan by dragging the right mouse button, zoom by dragging the middle button and rotate by dragging the left button. If you like a given representation of results and you want to reuse it you can save the Gfsview file ("Save" in toolbar) in gvf format, like vectors.gvf.
We can pipe the results at every time we want directly on Gfsview writing now the file.gts at every time
GfsOutputSimulation { time = 1} file.gts
and running
Gerris2D tutorial5.gts | Gfsview -s vectors.gfv
but stationary flows are stationary.
Adding objects
We will add a solid object in our channel, a cylinder. Gerris uses implicit functions to define solids, the Gerris word is GfsSolid and the syntax
GfsSolid ( implicit function )
by the way a circle of radius 0.125 at (0,0) is
GfsSolid (x*x + y*y - 0.125*0.125)
We also can refine the solid using the Gerris word RefineSolid like
RefineSolid 6
We note that Gerris can deal with arbitrarily complex solid boundaries (in gts format) embedded in the quad/octree mesh but creating polygonal surfaces is not an easy job and is explained in other tutorial. We use in this case the same Gerris word, GfsSolid mycomplexsurface.gts.
Now for our cylinder the script is
2 1 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsSolid (x*x + y*y - 0.125*0.125) RefineSolid 6 GfsTime {end = 5} SourceViscosity 1. GfsOutputLocation { step = 1 } data positionXYZ GfsOutputLocation { step = 1 } data0.45 positionX0.45YZ GfsOutputLocation { step = 1 } data1.45 positionX1.45YZ GfsOutputSimulation { time = 1} file.gts } GfsBox { left = Boundary { BcDirichlet P 1 } top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } GfsBox { right = Boundary { BcDirichlet P 0 } top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } 1 2 right
Saving the Gerris script on tutorial6.gfs and running
Gerris2D tutorial6.gfs Gfsview -s vectors.gvf file.gts
we can see the Benard-Von Karman wakes.
humm, let's go to a textbook...
Wake behind a cylinder
ah the Reynolds number have to be bigger than 50 and we need a long channel to allow the wake develops...
The Reynolds number is compute from the box of size 1 but for the specific case of the wakes behind of cylinder the typical length is the cylinder diameter. So Red = Re/4 because the cylinder diameter is L/4.
We add also 2 other boxes (we know how) and we set the Reynolds number to 100
the Reynolds number to 400. (which is 100. using the cylinder diameter), SourceViscosity 1./400. the final time to 10 GfsTime {end = 10} the final file results file10.gts at time 10 GfsOutputSimulation { start = end } file10.gts
The Gerris script is
4 3 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsSolid (x*x + y*y - 0.125*0.125) GfsTime {end = 10} SourceViscosity 1./400. GfsOutputLocation { step = 1 } data positionXYZ GfsOutputLocation { step = 1 } data0.45 positionX0.45YZ GfsOutputLocation { step = 1 } data1.45 positionX1.45YZ GfsOutputSimulation { start = end } file10.gts } GfsBox { left = Boundary { BcDirichlet U 1 } top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } GfsBox { right = BoundaryOutflow top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } 1 2 right 2 3 right 3 4 right
We found the following results
and the wake..? hum we will try a more discretized mesh, we set now
Refine 6
and now the famous wake appears!!!
conclusion : don't forget discretization!! It could be interesting to have a dynamical adaptive meshing.
Adaptive meshing
We are going to use dynamic adaptive mesh refinement, a very interesting characteristic of Gerris where the quad-tree structure of the discretization is used to adaptively follow the small structures of the flow, thus concentrating the computational effort on the area where it is most needed.
This is done using GfsAdapt which inherits (yet) GfsEvent. Various criteria can be used to determine where refinement is needed. In practice, each criteria will be defined through a different object derived from GfsAdapt. If several GfsAdapt objects are specified in the same simulation file, refinement will occur whenever at least one of the criteria is verified.
GfsAdapt is the base class for all the objects used to adapt the resolution dynamically, the parameters are
minlevel The minimum number of refinement levels (default is 0). maxlevel The maximum number of refinement levels (default is infinity). mincells The minimum number of cells in the simulation (default is 0). maxcells The maximum number of cells in the simulation. If this number is reached, the algorithm optimizes the distribution of the cells so that the maximum cost over all the cells is minimized (default is infinity). cmax The maximum cell cost allowed. If the number of cells is smaller than the maximum allowed and the cost of a cell is larger than this value, the cell will be refined. weight When combining several criteria, the algorithm will weight the cost of each by this value in order to compute the total cost (default is 1). cfactor Cells will be coarsened only if their cost is smaller than cmax/cfactor (default is 4).
We will use GfsAdaptVorticity defined as the norm of the local vorticity vector multiplied by the cell size and divided by the maximum of the velocity norm over the whole domain. The syntax is
GfsAdaptVorticity {inheritance GfsEvent} {inheritance GfsAdapt}
like that
GfsAdaptVorticity { istep = 1 } { maxlevel = 6 cmax = 1e-2 }
we can write now another Gerris script
4 3 GfsSimulation GfsBox GfsGEdge {} { Refine 5 GfsSolid (x*x + y*y - 0.125*0.125) GfsTime {end = 10} SourceViscosity 1./400. AdaptVorticity { istep = 1 } { maxlevel = 6 cmax = 1e-2 } OutputTime { step = 1 } stderr GfsOutputLocation { step = 1 } data positionXYZ GfsOutputLocation { step = 1 } data0.45 positionX0.45YZ GfsOutputLocation { step = 1 } data1.45 positionX1.45YZ GfsOutputSimulation { start = end } file10refine5adap.gts } GfsBox { left = Boundary { BcDirichlet U 1 } top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } GfsBox { right = BoundaryOutflow top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } } 1 2 right 2 3 right 3 4 right
and we can look the wake
and the mesh distribution
Two brothers or sisters of GfsAdaptVorticity are
- GfsAdaptGradient — Adapting cells depending on the local gradient of a variable
- GfsAdaptFunction — Adapting cells depending on the value of a function
and you can combine all together...
Passive tracer and Adaptive meshing
We continue to explore the adaptive meshing by the introduction of another basic concept, the passive tracer. Experimentalists use passive tracer (like ink) to visualize the fluid flows. Gerris can do that using GfsVariableTracer which advected a scalar quantity with the flow velocity, the syntax is
GfsVariableTracer tracer
by the way
GfsVariableTracer T
where T is the advected (scalar) quantity. We can also use the grid refinement of the variable T
GfsAdaptGradient { istep = 1 } {maxlevel = 6 cmax = 1e-2} T
we recognize the inheritance { istep = 1 } {maxlevel = 6 cmax = 1e-2}
We modify the boundary condition to have a thin jet of fluid at the entry and we inject the passive tracer inside,
GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } left = Boundary { BcDirichlet U ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) BcDirichlet T ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) } }
where ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) is a C shortcut of if variable y is between -0.05 and 0.05 set T to 1 and zero elsewhere. The new script is now
4 3 GfsSimulation GfsBox GfsGEdge {} { Refine 5 Time { end = 20 } GfsVariableTracer T SourceViscosity 1./400 GfsAdaptGradient { istep = 1 } {maxlevel = 6 cmax = 1e-2} T OutputSimulation { step = 1 } stdout } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } left = Boundary { BcDirichlet U ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) BcDirichlet T ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) } } GfsBox { } GfsBox { } GfsBox { right = BoundaryOutflow } 1 2 right 2 3 right 3 4 right
where we have take off the solid surface and the writing positions. Now we can save the file and pipe the stdout on GfsView to follow the dynamic of the entry jet
gerris2D tutorial7.gfs | gfsview2D
We show the velocity field and the passive tracer for two different physical times(t=1 and t=4).
File:tuto8-T.jpg File:tuto8-T-4.jpg
The following figure shows the mesh at different times
File:tuto8-G.jpg File:tuto8-G-4.jpg
We add diffusion to the tracers using the Gerris word SourceDiffusion like
SourceDiffusion T 0.001
and the solution for t=4 is now
we note that tracer can represent, for example, temperature or concentration.
(Less) passive tracer : VOF technique
We know that experimentalists use bubbles to analyze fluid flows (PIV). Bubbles can be a passive tracer but ... can be a field of study. Moreover every frontier separating two different fluid have potential interest in academic and industry.
Gerris uses a VOF (Volume Of Fluid) technique to follow interfaces, the VOF is a numerical technique for tracking and locating interfaces, in particular fluid-fluid ones.
Gerris first define the marker of the interface using GfsVariableTracerVOF which defines a volume-fraction field advected using the geometrical Volume-Of-Fluid technique, the syntax is
VariableTracerVOF tracerVOF
The tracer will be advected and we need to define the geometrical position of the boundary. To define the frontier Gerris uses the word GfsInitFraction with the following syntax
GfsInitFraction tracerVOF (implicit surface)
We add now a bubble of radius 0.125 L (recall that L is the size of the unit box)
VariableTracerVOF T1 GfsInitFraction T1 ((x)*(x) + y*y - 0.125*0.125)
and now our script is
4 3 GfsSimulation GfsBox GfsGEdge {} { Refine 5 Time { end = 20 } VariableTracer T VariableTracerVOF T1 InitFraction T1 ((x)*(x) + y*y - 0.125*0.125) SourceViscosity 1./400 GfsAdaptGradient { istep = 1 } { maxlevel = 7 cmax = 1e-2 } T1 GfsAdaptGradient { istep = 1 } {maxlevel = 6 cmax = 1e-2} T OutputTime { step = 1 } stderr OutputSimulation { step = 1 } stdout } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } left = Boundary { BcDirichlet U ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) BcDirichlet T ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) } } GfsBox { } GfsBox { } GfsBox { right = BoundaryOutflow } 1 2 right 2 3 right 3 4 right
where we added mesh refinement in the line GfsAdaptGradient { istep = 1 } { maxlevel = 7 cmax = 1e-2 } T1, the following figures show the two tracers T and T1 for physical times t=1 and t=4.
File:tuto9-T.jpg File:tuto9-T-4.jpg
Adding surface tension
Gerris can model the physical characteristics of the frontier (signaled by the tracer T1 in the last script), Gerris uses two reserved words
GfsSourceTension which adds a surface-tension term to the momentum equations, associated with an interface defined by its volume fraction and curvature. VariableCurvature which contains the mean curvature (double the mean curvature in 3D) of an interface
with the following syntaxes
GfsVariableCurvature variable-of-curvature tracer
and
GfsSourceTension tracer value-of-tension variable-of-curvature
Now to add a surface tension to our bubble we set
GfsVariableCurvature K T1 GfsSourceTension T1 0.01 K
which says rely the variable of curvature K to the tracer T1 and add a surface-tension term with constant tension equal to 0.01
The script is
4 3 GfsSimulation GfsBox GfsGEdge {} { Refine 5 Time { end = 20 } VariableTracer T VariableTracerVOF T1 InitFraction T1 ((x)*(x) + y*y - 0.125*0.125) GfsVariableCurvature K T1 GfsSourceTension T1 0.01 K SourceViscosity 1./400 GfsAdaptGradient { istep = 1 } { maxlevel = 7 cmax = 1e-2 } T1 GfsAdaptGradient { istep = 1 } {maxlevel = 6 cmax = 1e-2} T OutputTime { step = 1 } stderr OutputSimulation { step = 1 } stdout } GfsBox { top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } left = Boundary { BcDirichlet U ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) BcDirichlet T ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) } } GfsBox { } GfsBox { } GfsBox { right = BoundaryOutflow } 1 2 right 2 3 right 3 4 right
The figures show the jet pushing the bubble for times t=1, 4, 6, 8.
File:tuto10-T.jpg File:tuto10-T-4.jpg
File:tuto10-T-6.jpg File:tuto10-T-8.jpg
Breaking bubbles
What will happens if we lower the surface tension? Set now
GfsSourceTension T1 0.01 K
The figures show the jet pushing the bubble which now ... breaks!! (for times t=1, 4, 6, 8).
File:tuto11-T.jpg File:tuto11-T4.jpg
File:tuto11-T6.jpg File:tuto11-T8.jpg
and the grid and a little (big) zoom for time t=8
File:tuto11-T8Grid.jpg File:tuto11-T8zoom.jpg
It is interesting to note that in the grid figure above Gerris uses 3232 mesh points (or squares). Without adaptive mesh refinement we must set 4 boxes of 64x64 or more of 128x128 because the frontier needs a 7 level refinement so
3232 or 16384 or 65538
you have the choice.
Gerris in parallel
One of the human's dreams is to run a program in parallel, Gerris allows do it quite easily, for instance if you want run our last script in four processors we have to modify only the boundary conditions using the Gerris word pid like
GfsBox { pid = 0 top = Boundary { BcDirichlet U 0 BcDirichlet V 0 } bottom = Boundary { BcDirichlet U 0 BcDirichlet V 0 } left = Boundary { BcDirichlet U ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) BcDirichlet T ( (y > -0.05 && y < 0.05 ) ? 1 : 0 ) } } GfsBox { pid = 1 } GfsBox { pid = 2 } GfsBox { pid = 3 right = BoundaryOutflow }
and run the script with
mpirun -np 4 gerris2D tutorial2.gfs
What we do is an example of manually partitioning the domain. In more complex cases, Gerris can also automatically partition the domain for a given number of processors, variable resolution, complex boundaries.
Therefore we can now begin a good Saturday night saying
You know sweet, I can run parallel programs...
success assured!!
Les mots et les choses
∂/ ∂tu + u∇.u = 0